| Surface roughness | Rtmax | Ra |
| Sliding surface | ≤ 2.5 µm | 0.1–0.5 µm |
| Slot bottom | ≤ 6.3 µm | ≤ 1.6 µm |
| Slot side | ≤ 15 µm | ≤ 3 µm |
| Bearing area: 50-95% and 0.5 Rz cutting depth (based on Cref = 0%) | ||
| Recommended Size mm | Maximum gap mm | ||||||||
| d/f8 | D/H10 | L/+0.2 | Rmax | C | s* | ||||
| ＞ | ≤ | 20 bar | 100 bar | 200 bar | 400 bar | ||||
| 5 | 25 | d + 8 | 6.3 | 0.4 | 3.5 | 0.33 | 0.18 | 0.10 | 0.05 |
| 25 | 50 | d + 10 | 8.0 | 0.4 | 4.0 | 0.37 | 0.23 | 0.15 | 0.10 |
| 50 | 150 | d + 15 | 10.0 | 0.4 | 5.0 | 0.46 | 0.33 | 0.25 | 0.18 |
| 150 | 300 | d + 20 | 14.0 | 0.4 | 6.0 | 0.54 | 0.38 | 0.33 | 0.25 |
| 300 | 500 | d + 25 | 17.0 | 0.4 | 8.5 | 0.61 | 0.45 | 0.40 | 0.33 |
| 500 | 600 | d + 30 | 25.0 | 0.4 | 10.0 | 0.67 | 0.50 | 0.45 | 0.40 |
| 600 | 1000 | d+40 | 32.0 | 0.4 | 13.0 | 0.67 | 0.50 | 0.45 | 0.40 |
| 1000 | 1600 | d+50 | 40.0 | 0.4 | 15.0 | 0.80 | 0.60 | 0.50 | 0.40 |
| 1600 | 2000 | d+60 | 47.0 | 0.4 | 18.0 | 0.90 | 0.70 | 0.50 | 0.40 |
| 2000 | 2500 | d+80 | 62.0 | 0.4 | 20.0 | 0.90 | 0.70 | 0.50 | 0.40 |
| The extrusion gap values shown in the table above apply to temperatures below 70 °C. Higher temperatures require lower extrusion gaps. |
|||||||||
| Operating parameters | |||||
| Material | Temperature | Speed | Pressure | ||
| Sealing components | Elastomer | Minimum °C | Maximum °C | Maximum m/s | Maximum bar (MPa) |
 PU |
NBR70 |
-30 | +100 |
0.5 | 400 (40) |
 HPU |
-20 | ||||
 SPU |
0.7 | ||||
 TPU |
MVQ70 |
-50 | +110 | 0.5 | |
| Ordering example | |
| Introduction | Rod seal TS03-P |
| d x D x L [mm] | 100 x 115 x 10 |
| Sealing material | PU / NBR 70 |
Product classification
Label List
Previous Page
TS03-FS
Next Page
Free inquiry
