| Surface roughness | Rtmax | Ra | Rtmax | Ra |
| Sliding surface | 12,5 | 3,2 | 6,3 | 1,6 |
| Trough bottom | 12,5 | 3,2 | 6,3 | 1,6 |
| Trough side | 12,5 | 3,2 | 6,3 | 1,6 |
| Bearing area: 50-95% and 0.5 Rz cutting depth (based on Cref = 0%) | ||||
| Recommended Size mm | ||||||||||
| OD | t | L | t1 | L1 | L2 | R | hst | c | s | |
| AS/568A1) | ISO/36012) | |||||||||
| 1,78 | 1,8 | 1,35 | 2,5 | 1,58 | 3,5 | 4,5 | 0,3 | 1 | 3 | f7/H8 |
| 2,62 | 2,65 | 2,18 | 3,5 | 2,42 | 5,0 | 6,5 | 0,3 | 1,5 | 3,5 | f7/H8 |
| 3,53 | 3,55 | 3 | 4,4 | 3,70 | 5,9 | 7,4 | 0,5 | 1,5 | 4 | f7/H8 |
| 5,33 | 5,3 | 4,5 | 6,7 | 5,60 | 8,4 | 10,1 | 0,6 | 1,7 | 5 | f7/H8 |
| 6,99 | 7 | 5,94 | 8,8 | 7,37 | 10,8 | 12,8 | 0,8 | 2 | 6 | f7/H8 |
| 10 | 10 | 8,5 | 12,5 | 10,5 | 15,0 | 17,5 | 1 | 2,5 | 10 | f7/H8 |
| 12 | 12 | 10,2 | 15,5 | 12,85 | 18,5 | 21,5 | 1 | 3 | 12 | f7/H8 |
| 15 | 15 | 12,75 | 19 | 15,88 | 22 | 25 | 1 | 3 | 15 | f7/H8 |
| The extrusion gap values shown in the table above are applicable to temperatures below 70°C. Higher temperatures require lower extrusion gaps. | ||||||||||
| Operating parameters | ||||
| Material | Temperature | Speed | Pressure | |
| Sealing components | Minimum °C | Maximum °C | Maximum m/s | Maximum bar (MPa) |
 PU |
-30 | +110 | Recommended for static applications |
600(60) |
 HPU |
-20 | |||
 SPU |
||||
 TPU |
-50 | |||
 NBR |
-30 | +100 | 160(16) | |
 FKM |
-20 | +200 | ||
 EPDM |
-50 | +150 | ||
 HNBR |
-25 | |||
 MVQ |
-60 | +200 | ||
 PTFE v |
-200 | +260 | ||
| Ordering Example | |
| Introduction | Static Seal TR13 |
| d x OD [mm] | 100 x 3.5 |
| Sealing Material | PU |
Product classification
Label List
Previous Page
TR14
Next Page
Free inquiry
